|
Galaxie 500 Site: Ford Restoration Q&A
Do you have a Ford restoration question or a response to a message below?
Messages about items for sale or wanted will not be posted.
Click on the "Respond" button to enter a response to its respective question.
Search the archive for answers to your questions before you post them.
DISCLAIMER. The Galaxie 500 Site and its owner are not liable
or responsible for any responses to questions that are not correct and
slanderous. Those asking questions and those responding are responsible for the
validity of all information received. We suggest that you please check out all
responses before implementing changes to your car. Anyone that may have been
falsely represented by a response or question may respond to protect their
reputation, but must respond with proof to defend their
position.
This Restoration Q&A is not in any way affiliated with the Ford Motor Company or any of its subsidiaries.
|
|
|
|
|
|
|
|
 |
Question From:
Mike
2012-02-03
1966 Ford Galaxie 500 2 Door Fastback
| Question:
I want to replace/convert the single speed wiper motor with a two speed. Any tips on what motor would work with my vehicle and would this type of motor change require running seperate wiring to do so? Please advise.
Response(s)
|
| Question From:
keith
2012-02-02
1966 galaxie 500
| Question:
Will a 429 (thunderjet) out of a 1968 Thunderbird fit in a 1966 Galaxie 500 that came with a 390? Will the motor mounts on the engine and the frame match up?
Response(s)
|
| Question From:
Ray anos
2012-02-02
1964 Ford Galaxie 500 66
| Question:
Why is there a 66 after a 1964 Ford Galaxie 500 66?
Response(s)
|
| Question From:
Travis Taylor
2012-02-02
67 Galaxie 500 XL
| Question:
I need to know the rear wheel cylinder sizes for a 67 Galaxie 500 XL 390. 15/16 or 29/32?
Response(s)
had the same question myself while replacing cylinders on my 66. what i found was that usually the larger of the cylinders were used on the xl and the 7 ltr. the larger ones are just a little more heavier duty than the small. i went with the 15/16 cause you can never have too much stopping power.
|
| Question From:
brett
2012-02-02
1968 Galaxie
| Question:
How do you get the chrome off the side?
Response(s)
can you be a bit more specific.
|
| Question From:
Joel
2012-02-02
1959 Ford Fairlane
| Question:
The driveshaft won't come loose from the transmission. Is there a lock of some sort ?
Response(s)
|
| Question From:
Travis
2012-02-01
1964 Ford Galaxie 500
| Question:
Hi, I have a 1964 Galaxie 500 two door fastback with front bench seats. I would like to put in some casual racing seat belts and the bucket seats from the xl version. Will the seats fit in my Galaxie?
Response(s)
they should fit. you will have to drill holes for the tracks of the buckets i think.
|
| Question From:
Colton S.
2012-02-01
1967 Ford Galaxie 500
| Question:
Hi, I am buying a 1967 Ford Galaxie 500 4dr with a 390 cu.i v8 two-barrel. It needs the ball joint (front) replaced and it needs re-wired. How much will this cost? I am a diy guy so ill just need to find the parts. the interior needs to be redone as well. any tips, etc will be appreciated.
thanks.
Response(s)
|
| Question From:
Tony
2012-02-01
1963 For Galaxie 6cyl
| Question:
My sons 1963, 6cyl, will not start or do anything when the key is turned. If I jump ground to the red/blue wire on the starting solinoid it will start, but only run off of the battery. The Gen light comes on, but I think that is because the regulator is not working right or not getting a right input, i.e. the ground to the red/blue wire. This wire runs all the way to the ignition switch, but I cannot see to jump it to ground any where else to get the car to start. Getting confused in Iowa.
Response(s)
|
| Question From:
Art
2012-02-01
1966 Ford Galaxie 500 2 door hartop fast
| Question:
I am taking the body off the frame and the 4 bolts at the firewall are turning and there is no place from under the frame to get into that area to put a socket or wrench. I hate to cut them off. Does anyone have a suggestion. Has anyone ran acroos this problem?
Response(s)
|
| Question From:
bill ferrazzano
2012-01-31
1965 Galaxie 500 with a 390 motor
| Question:
Can someone tell me the right color to paint my 1965 Galaxie 500 with a 390 motor (valve covers and air breather).
Response(s)
|
| Question From:
DAN McDONALD
2012-01-31
1960-62 Ford Starliner Hardtop
| Question:
Does anyone know if the rear electric quarter window regulators in a 1960 & 61 Starliners are the same as the 1961-62 Galaxie 2 dr hardtop model 65a & 65b. (NOTE) The hollandar interchange does not have this info. Probably in a Ford shop service manual which I don't have. Thanks DAN. (608) 963-0090
Response(s)
|
| Question From:
Richard Napier
2012-01-31
1968 Ford Galaxie 500 XL 390
| Question:
What are 1968 Ford Galaxie 500 XL with the 390 engine in very restorable condition going for (ballpark figure)
Response(s)
|
| Question From:
tom gordon
2012-01-31
1962 Ford Galaxie 500 xl
| Question:
Do 1962 Galaxie 500xl's have external screws to hold rear quarter panel mouldings on and what is the difference between the 390 300hp and the 330hp engines?
Response(s)
|
| Question From:
David Thomas
2012-01-30
1964 galaxie 500 fastback
| Question:
Hello I was curious how to change out my ignition on my 64 Galaxie 500 fastback? Thanks for your time. Dave
Response(s)
|
| Question From:
Phil Wulf
2012-01-30
1968 Galaxie 500 XL convertable
| Question:
Where can I find a diagram for hooking up my vacum lines on my 68 Galaxie 500 XL with the hidden headlights. Also looking vor a wiring diagram as I got it only partially reassembeled after having many parts rebuilt or replaced.
Response(s)
|
| Question From:
ray warren
2012-01-29
1969 ford ltd
| Question:
what is the color for 1969 ford ltd vin 65a-6aa-14b-4-w-11015
Response(s)
|
| Question From:
Frank A
2012-01-29
1965 Ford Galaxie
| Question:
What is the largest tire, wheel for the rear of 1965 Ford Galaxie?
Response(s)
|
| Question From:
John Hodges
2012-01-28
1964 Galaxie 500 fastback
| Question:
What is the correct engine color and valve cover color for a 1964 galaxie 500 289?
Response(s)
|
| Question From:
Bjorn Dahlheimer
2012-01-28
1959 Ford Fairlane Galaxie 500
| Question:
Have a '59 Ford Galaxie Fairlane 500. Does any one know which transmission fluid and rear axle fluid I should use?
Response(s)
|
| Question From:
Bill
2012-01-27
1966 Ford Galaxie 500 Convertible / 352
| Question:
I need reference pictures of the stock, factory engine of the 1966 Galaxie 500 convt 352. I can't seem to find them online and if any leads or tips on how i can get the please forward them.
Thanks!
Response(s)
|
| Question From:
ted illsley
2012-01-26
1963 Ford Galaxie 500 XL
| Question:
I am restoring a 1963 Ford Galaxie 500XL convertible with damaged sisscor section of the top frame above the door and side windows.will the sisscor section from a 1964 galaxie interchange with the 1963?
Response(s)
|
| Question From:
SCOTT GAMACHE
2012-01-24
1967 Ford Galaxie 500 Convertible
| Question:
How do you remove the ash tray on the dash of a 1967 Ford Galaxie?
Response(s)
|
| Question From:
Brendan
2012-01-21
1967 Galaxie 500
| Question:
I have a 67 Galaxie 500, and the tank is rusted out. I cleaned and sealed it but I am still getting little flakes of rust, so I think its time for a new one. The cheapest one I can find is 300, but I found one that works for a 69 or 70 for 200, the dimensions make it sound like it should fit, but has anyone ever heard of using these tanks interchangeably?
Response(s)
|
| Question From:
Myron Rathjen
2012-01-21
1963 Ford 500 Galaxie 500 Convertible
| Question:
How are the lower control arms on a 1963 Ford Galaxie XL removed?
Response(s)
|
| Question From:
Mike S
2012-01-21
1967 Galaxie 500 2 door fastback
| Question:
I've hunted the web for interior, exterior and electrical assembly manuals for my '67 but have only found the engine assembly manual. Do the others even exist or are they covered by the Ford shop manual, which I have? If they exist, does anyone know of a source? Thanks
Response(s)
|
| Question From:
Leroy
2012-01-20
1969 Galaxie 500 2dr fastback.
| Question:
I need some help on how to attach the cowl trim at the bottom of the windshield. The two pieces match in the middle and there is a place for a screw but not sure what to screw it into. Is there supposed to be a metal piece with a threaded hole?
Response(s)
|
| Question From:
seth madison
2012-01-20
1966 Ford Galaxie 500
| Question:
Hi, was wondering if anybody could tell me the location of the block VIN number cuz I'm trying to figure out what motor is in my 66 Galaxie 500. It has a 390 emblems on it but I keep hearing different things about different motors in it so I am just trying to figure it out so then I can start my restoration on the vehicle. Thankx and please get back to me as soon as you can.
Response(s)
I have a 66 Gal Conv
First the vin on the car will tell you what engine it left the factory with
5th position will be a letter
X= 352 4BBL
Z= 390 2BBL
R= 428 4BBL
you can look in this site to help you decode the vin
As far as engine, if it is an FE(352) series motor, it will have a raised 352 in the drivers side just below the cylinder head on the block near the water pump plus the valve cover rail is part of the intake manifold
If it is a small block, ie 289,302 then the will not have the valve cover rail as part of the intake.If i remember, the only choices are 289,302,352,390,and 428 cid
If someone put in a "385" series motor, 429 or 460 cid, it will have 385 raised in the same place on the block below the head drivers side
good luck
|
| Question From:
Dan Sommerfeld
2012-01-20
1964 Galaxie 500
| Question:
I want to put seat belts in my 64 galaxie 500. I have found the front seat mounts for belts but I did not locate mounting holes for the rear seat. Does anyone know if there are holes for the rear belts. Thanks Dan
Response(s)
there were no seat belts in the rear of the 64 if you want rear belts you will have to find a good mounting point and drill holes for the belts
there were no seat belts in the rear of the 64 if you want rear belts you will have to find a good mounting point and drill holes for the belts
|
| Question From:
Tim
2012-01-17
1967 Ford Galaxie 500
| Question:
I have a 1967 Galaxie 500. Does not have a drive shaft. I need to know whats a good company that can make one and also need the length of it.
Response(s)
I have three drive shafts that came out of 1967 Galaxies. Where you located? I'm near Austin, TX.
|
| Question From:
jeff
2012-01-17
1968 Ford Galaxie XL
| Question:
Will other Ford 68 radios fit in my 1968 Galaxie XL? Looking to replace my AM with a AM/FM.
Response(s)
you will have to cut the hole larger to allow the AM/FM radio. I have one in my 68 conv. The face plate is larger. I my have an extra radio in my stash.
|
| Question From:
dave tober
2012-01-16
66 galaxie 500
| Question:
I have a 1966 Galaxie 500, will the new door panel trim for a 67 XL or 500 work on a 66 they look very similar?
Response(s)
|
| Question From:
Luke
2012-01-16
1965 Ford Galaxie 500 4 door
| Question:
Having trouble getting bolts off for the front bench seat in my 1965 4 door Ford Galaxie 500. Does anyone have any suggestions?
Response(s)
Good evening. Try spraying them with Kroil Oil. This is the best stuff for loosening rusty or tough bolts, nuts, etc. It beats everything else on the market.
|
| Question From:
bill ferrazzano
2012-01-13
1965 Galaxie 500 Convertable
| Question:
How do you remove the wiper switch on a 1965 Galaxie 500?
Response(s)
|
| Question From:
ken
2012-01-13
1963 1/2 Galaxie fastback
| Question:
1963 1/2 Galaxie fastback. Will I be able to install a 427 w/stock headers 4 speed trans as one unit?
Response(s)
you will be able to drop in the motor/trans .but not with the headers unless they are factory shorties, lond tube headers will need to be fitted around steering box and small high torque starter installed
|
| Question From:
jeff dechenne
2012-01-12
65 Galaxie Convertible
| Question:
I have a 65 Galaxie Convertible. 390 car has a cruise-o-matic. Will a C6 fit?
Response(s)
I swapped my cruise-o-matic for a C6 in my 289 65 Galaxie no problem. I used a Lokar kit to connect the column shifter. I had to slide the crossmember back to line up the transmission mount. My car did not come with a driveshaft, so I had one made.
|
| Question From:
Fran Summers
2012-01-11
Ford Galaxie 500
| Question:
What year did they make the last Galaxie 500?
Response(s)
1974.
|
| Question From:
vince
2012-01-11
1969 Ford Galaxie 500
| Question:
I need to find a wiring diagram for a 1969 Galaxie 500 that I can download.
Response(s)
Try this site. They should have it..
http://www.tocmp.com
|
| Question From:
Wshort
2012-01-10
1967 Galaxie 500
| Question:
Needing a 1967 Galaxie 500 hood. Not having good luck in my area. Anyone know if any Lincoln/Mercury hoods will fit?
Response(s)
What area are you in? I know a salvage yard with several 67 Galaxies in it. Most are 4-doors, but the front is all the same. I am in West Tennessee.
|
| Question From:
mario
2012-01-10
1964 Galaxie 500 Convertible
| Question:
I just got a 1964 Galaxie 500 convertible that is said to have a 352 and has a 4 bbl carb. I thought only XL's had a 4 bbl with this engine. How do I find out what I have for sure?
Response(s)
use this site to decode your vin
I have a 66 Gal 500 not XL and it came with 352 4BBL vin "X" in fifth position
|
| Question From:
josh robertson
2012-01-09
1966 Ford Galaxie 500
| Question:
I have a 1966 Ford Galaxie 500 I just switched to a 81 Ford distrbotur tryn 2 find the right timing. Plus need help with a lowering kit and a conversion kit 4 my aod trans.
Response(s)
|
| Question From:
Liberty King
2012-01-09
1967 Ford Galaxie 500 2 dr. H.T. fastbac
| Question:
I need to replace the fuel sending unit in my 1967 Galaxie 500 2 dr . H.T. fastback. Do I have to remove the gas tank?
Response(s)
I am going to say no. It will probably be a pain, but it can be done. I of course recommend to everyone to buy a service manual. Best money you can spend.
I just bought the same car and need to replace the sending unit too. I have a dumb question; since the sending unit is mounted on the side of the gas tank does it need to be emptied first? How expensive is it?
took mine out of a 66 convert without dropping tank
you need jack stands, creeper and work light i suggest some goggles to keep stuff out of your eyes
|
| Question From:
jim burnett
2012-01-08
1961 Galaxie
| Question:
1961 Galaxie want change man. steering box to power box what will work? Willing to do some mod.
Response(s)
any 61-64 ford power steering unit will work
|
| Question From:
Werner
2012-01-08
1972 Galaxie 500 4dr sedan
| Question:
Hello, Is there a way to find the production date (even approximately, say a month) from only the VIN? I have a model 1972 Ford Galaxie500 4dr sedan. It's an export (sold originally by Ford in Belgium, EU. Production plant is Norfolk, VA, USA. I contacted Ford USA headquarters, but they need the codes on the door tag. The problem is, the door tag is missing, from a previous restoration (or exports never had one?). The only identification it carries (besides its Belgian registration papers) is a Belgian VIN fender plate from Ford Motor Company Antwerp (it only shows VIN, a Belgian/European Type-approval code, Weight and Max.Towing Weight). Does anyone have datasheets showing production months for VIN serial nr ranges? For example "from 2N54H-111111 to -222222 = nov 1971", etc...? For a (very rough) estimate: I did find a number 72 in a dotted circle, stamped in a bracket of the steering column. Assuming that is still the original part, that would date it to somewhere in 1972, instead of late 71, I guess? Also: engine code H (351 2barrel V8), is that the Windsor or Cleveland motor? Thanks, Werner
Response(s)
|
| Question From:
Kip
2012-01-06
1968 Ford Galaxie 500 conv
| Question:
I have a 1968 Galaxie 500 conv with a severely rusted frame, are any other years or hardtop frames the same?
Response(s)
Your frame interchange is 65 - 68 with only some minor variations over the years. 2 door and 4 door are the same. Convertables are different.
I have a 1968 Galaxie 500 Convertable. The only issue I have had with any rusting is the floor pans, due to sitting in yard for a couple years. My frame is in great shape and the body has never been wrecked.
I found a few small holes in the bottom of the rectangular tubes that run front to back on my 68 LTD when sandblasting. I had a metal fabricator bend me some 11 gauge channels that came up the sides an inch and welded into good metal. The body had to be lifted but not completely removed. The inside was soaked in rust killer and sealers, etc. This may work for you if it is the same area. I can get you the name and number of the guy that made the parts and he probably still has the drawing that I sent him.
|
| Question From:
Ron Kinberger
2012-01-06
1964 Galaxie 500 xl 390
| Question:
I have a 64 Galaxie 500 XL 390 Eng. I need the specs for turning the the front and rear drums. Orielys can turn the drums but they cannot find the specs to see if they are legal.
Response(s)
I got these specs from this website. I clicked on the image and the max dia. is listed as 11.09". Several other sites has the same information.
http://www.r1concepts.com/ford-galaxie-1964-exc-122.61003A.htm
|
| Question From:
Luke
2012-01-06
1963 Galaxie 500
| Question:
I have a problem with the gas pedal and throttle. The pedal is loose and does not pull enough on the throttle lever to give the engine gas. Is there a way to adjust, modify the gas pedal so it has no give?
Response(s)
|
| Question From:
jimmy
2012-01-05
1963 Galaxie
| Question:
I am trying to buy a 1963 Galaxie, it has a 406 with three 2 barrels & auto trans. Can anyone tell me if that is that is a corrert combo?
Response(s)
If you have the VIN, then you can decode it here.
http://www.decodethis.com/3P66Z169959
|
| Question From:
alan everk
2012-01-05
1964 Galaxie 500
| Question:
I'm rebiulding the front end on my 64 Galaxie and I am putting new shafts and bushings in the upper control arms. I know that there is a Ford tool for this but I can't locate one. Is there anybody that will sell me one or can you give me an idea of how to center the shaft while I'm screwing the bushings in. Any help is appreciated.
Response(s)
I know this is not much help but look at these sites. The owner made a simple centering tool. It also appears that you also need some sort of stabilizer to "fix" a design problem.
http://www.kuumakyyti.com/ragtop64/
http://www.fordmuscleforums.com/galaxie-pages/507550-64-upper-control-arm-shafts.html
http://www.fordmuscleforums.com/suspension-articles/485352-60-64-galaxie-lower-arm-offset-shaft-eliminator.html
|
| Question From:
Maury Kurpies
2012-01-04
1968 Ford Galaxie 500 Sedan
| Question:
I would like a manual that shows how to restore a 1968 Ford Galaxie 500. Does such a manual exists?
Looking to restore body, chrome and some minor rust around the battery compartment. I would like to do the work myself to perfection. Any help will be appreciated.
Thank you!
Response(s)
Try this.
http://www.fordmanuals.com/estore/scripts/prodView.asp?idproduct=349
|
| Question From:
gary
2012-01-04
1964 Ford Custom 2 dr sedan
| Question:
Guys, I need a split front bench seat and complete rear seat for a 64 Galaxie Custom 2 door sedan. What other year Galaxie sedan seats will work in a 64? Thanks gn
Response(s)
|
| Question From:
Stuart
2012-01-02
1966 ford galaxie
| Question:
Went to replace the starter ignition switch and new switch is a whole different setup as fire as wiring and pigtail goes. Can anyone tell me how to wire up a replacement starter switch purchased from autozone?
Response(s)
|
| Question From:
Troy Cole
2011-12-31
1963 Ford Galaxie 500
| Question:
Installed power breaks on a 1963 Ford Galaxie 500. Do they make 14 inch wheels that will work with power brakes? Any suggestions?
Response(s)
Power brakes should NOT make a difference. 14" wheels will fit. However, if you added disk brakes, then no.
dearborn classics had a disc brake conversion for 14 in wheels,power brake add on is easy just get the correct booster there all over.
|
| Question From:
tom
2011-12-31
1972 LTD Convertible
| Question:
Does anyone know where I can buy restoration parts for a 1972 ltd convertible?
Response(s)
Try Dennis Carpenter, MAC's, Dearborn Classics, E-bay. Google is our friend.
|
| Question From:
Rudy Machacek
2011-12-30
1966 Galaxie 7 Litre
| Question:
How do you remove the dash trim plate on a '66 Galaxie? Specifically how do you remove the vent knobs? Does anyone have an assembly diagram?
Response(s)
|
| Question From:
Trino
2011-12-30
65 Gallaxie 500 ltd
| Question:
Hi I have a 65 Galaxie 500 ltd. It does run and drive with only 65k on the odometer. Although it is a four door it is all original with all the bells and wistles. I am wanting to do a body on frame restore but not too sure where to start and where to look for replacement parts. Thinking maybe JC.
Response(s)
Not JC
Try Dearborn Classics or Mac's
Craigslist is a good site and eBay
eBay-beware of people not knowing what they have for sale
|
| Question From:
Glen Davis
2011-12-28
1964 Ford Galaxie 500 XL
| Question:
Where can I buy a console neutral switch for a 1964 Ford Galaxie 500 XL?
Response(s)
|
| Question From:
juan aguilar
2011-12-27
1969 Galaxie Convertible
| Question:
I am looking for scuff plates for my 69 Galaxie convertible, but they dont't sell new ones. I am wondering is there any other year that will fit my car 68 or any year or model?Thanks. JJ AGUILAR
Response(s)
check out dearborn classics...i believe they sell them
|
| Question From:
Brandon Miller
2011-12-27
63 Ford Galaxie
| Question:
I have a 63 fastback with a 390. The starter needs to be replaced and I cannot get clearance to pull the starter out. Anybody else have problems with this and any hints to make it easier?
Response(s)
|
| Question From:
MICHAEL JAMESON
2011-12-26
1968 Ford Galaxie XL
| Question:
I am looking for an assembly diagram for radiator support, fenders and associated parts to the nose of a 1968 Ford Galaxie.
Response(s)
Try this. http://www.fordmanuals.com/estore/scripts/prodView.asp?idproduct=349
--------------------------------------------------------------------------------
|
| Question From:
Richard Gilbert
2011-12-26
1964 Galaxie 500xl
| Question:
Is there a wrong way to install front springs on a 64 Galaxie 500XL? Want to make sure I don't put them back the wrong way.
Response(s)
no they are the same on both ends.no wrong way to put them in
yes you can put them in upside down, the top of the spring is flat and finishes with a taper, the bottom ends in the termination of a coil, there is a recess in the lower control arm that it fits into, there is a rubber spring silencer that goes in the topa that fits around the spring relief, if you look closely at you springs you will notice that they will only stand up on the ground on one end, that is the top.
|
| Question From:
William Bryant
2011-12-26
1966 Ford LTD
| Question:
Will a 1966 Ford Fairlane GT hood with the chrome 390 inserts fit a 1966 Ford LTD?
Response(s)
No,the Fairlane is whole different car.
|
| Question From:
alan everk
2011-12-25
1964 Ford Galaxie 500 fastback
| Question:
I have a 1964 Galaxie and I'm looking for the piece that is welded to the floor and connects to the frame. It has the rubber body mount in between them. I don't know what it's called and can't find them anywhere. I would like to get a new one instead of just welding in pieces to fix it. Does anyone know if they are available? Thanks for your help.
Response(s)
|
| Question From:
John Hodges
2011-12-23
1964 Galaxie 500 fastback
| Question:
What's the best way to lift the body off the frame for my 64 Galaxie 500 fastback? I was thinking of using 2 or 3 floor jacks and some beefy timbers under the floor that would span across the width of the car just inside the frame rails. Any tips or suggestions?
Response(s)
I built a wooden platform with wheels so that i could lift the body (went from the front body mounts with one come along and jthe trunk with a chain in it to another comealong. worked good
|
| Question From:
Mark Schrade
2011-12-21
1962 Galaxie 500
| Question:
Have a 1962 Galaxie 500 that does not have side view mirrors. Where is the recommended location to properly install mirrors? On the door or where on the fenders?
Response(s)
they were located just in front of the vent window.the easiest way to set the location is to open the vent window and place the mirror on the door about 1.5 inches in front of the vent window while it is open .
|
| Question From:
Jeffrey Kroll
2011-12-21
1968 Ford Galaxie Convertible
| Question:
I have a 1968 Ford Galaxie Convertible with a factory 302. I am planning to install a 460. Please inform me in detail what would have to be changed to make this possible. Thank- you
Response(s)
you will need motor mounts , radiator , front coil srings , trans crossmember adapter .you can find all the parts at crites preformance.com
|
| Question From:
George Haynie`
2011-12-20
1967 Galaxie 500
| Question:
Where to buy parts for a 1967 Ford Galaxie 500?
Response(s)
dearborn classics
try rockauto.com then search for your model (1967 ford galaxie 500) then choose your engine size and you can purchase parts there pretty cheap
|
| Question From:
JIM
2011-12-20
1966 Galaxie 7 litre Convertible
| Question:
Will 1965 Galaxie (2 and 4 door) rear floor pans fit (look the same too) my 1966 Galaxie convertible?
Response(s)
|
| Question From:
Robbie
2011-12-20
1966 Ford Galaxie 500 7 Litre 2 door FB
| Question:
On my Q code 1966 Ford Galaxie 500 7 Litre 2 door fastback where would I find the numbers on my 428 4V that would prove I have a numbers matching car. And what will I be looking for?
Response(s)
the engine does not have the same #`s as the car . the engine #`s wil only tell you if the engine is the same year . they will be located just in frot of the passanger motor mount . and on the head under the valve cover . c6 is the main # your looking for
|
| Question From:
Al
2011-12-18
1961 Galaxie Sunliner
| Question:
Can the steering box be adjusted to take up a lot of play?
Response(s)
if it has a lot of play in it then it needs rebuilding
|
| Question From:
Don Timony
2011-12-11
1967 Ford Custom
| Question:
I have a 1967 Ford Custom and a frame from a 1967 Galaxie convertible. I want to transplant the convert frame under my Custom. I know the convert frame has brackets off the front for the front mounting and the Custom bolts to the torque box's up front which shouldn't be a problem. As far as any other concerns or possible differences you may know of would be greatly apprceiated.
Response(s)
If it dont work i want to buy that 1967 frame
If it dont work i want to buy that 1967 frame
If it dont work i want to buy that 1967 frame
If it dont work i want to buy that 1967 frame
|
| Question From:
Anthony Sanchez
2011-12-10
1964 Galaxie Country Squire
| Question:
First time forum user, I just acquired a one owner 1964 Galaxie Country Squire 289/AT 55k miles from an 85 year old woman. (sitting since 1985 covered carport) Paid $4K, super solid has not run since late 80's still has the stainless poverty caps. Faded one repaint, a little pitting on the luggage rack and a small rust spot on the roof. I would like to refurb the fake wood grain trim / and install new vinyl (removed years ago flaked off). It has all of the stainless buttons over the trim what tool would I need and any instructions/tools from removal to re-install would be great? I also have 69 Galaxie 500 2-door Hardtop in the fix up phase. Thanks.
Response(s)
My name is Ed i also have a 1964 country squire and am in the process of a total frame off restoration i was able to get the caps off with a putty knife that i grinded down to make it real thin they came right off and did not damage any of them. the best match i have found so far for the vinyl is from metro fefinishing.com marine teak color the fiberglass trim i stripped to bare plastic then used polyprime sanded and re primed then i had a company add a water transfer woodgrain film and then i clearcoated the trim looks better than new been doing this car for two years now cant find the rear tailgate rubber anywhere any help with that would be great good luck
|
| Question From:
josh
2011-12-09
1966 Ford Galaxie
| Question:
Hi I am about to buy this 1966 Ford Galaxie with 88,000 miles on the orignal engine and transmission. The interior is in great condition no rips tears or stains. The owner has taken care of it. I just want to make sure I am not getting ripped off and what is a good price to pay for this car?
Response(s)
A good price would up to $5000.
|
| Question From:
Chris
2011-12-08
1964 Galaxie 500 XL
| Question:
Does anyone sell a power steering box rebuild kit or remanufatured power steering box for a 1964 Galaxie?
Response(s)
Macs or Dearborn classics
|
| Question From:
mike
2011-12-08
1967 Ford Galaxie 500
| Question:
I have a 67 Galaxie and I am trying to remove the rear brake drums. I have adjusted the shoes all the way in and still can't get the drums off. Any suggestions would be appreciated. Thanks.
Response(s)
If you've already tried a drum puller and it didn't come off I would do the following.
a)remove the brake cylinder bleeder screw just in case some pressure is keeping the shoes out against the drum.
b) loosen the emergency cable adjuster to that wheel. Sometimes the cable is so tight that it will keep the shoe out and against the drum
c) grind off the heads of the hold down pins on the backing plate for the primary and secondary shoes. This will free the shoes up and might let the drum off.
|
| Question From:
eddie godsey
2011-12-06
1961 Ford Fairlane
| Question:
Will a 289 hp mate up to a 3 speed manual trans that came stock in a 1961 ford fairlane 6 cylinder 223 cubic inch?
Response(s)
No, the early OHV sixes (215, 223, 262) had their own bellhousing patterns.
|
| Question From:
ken ostrander
2011-12-06
1964 Galaxie
| Question:
How many engines where used in the Galaxie?
Response(s)
Ken, In 1964 the basic Ford came standard with a big 6 cylinder 223 CI, after that all the rest are V8's, the 289 is standard for big Fords, the 260 is available but not for the Galaxie, it's too small in HP, but the same block.
289
352 only a 4 barrel carb and hipo in the 1964
390
427
all motors except the 352 and 427 in 1964 came with either 2 or 4 barrel carb setup. There are several different versions of horsepower in each model engine. There are dual 2 barrels, dual 4 barrel carbs 3 2 barrel carbs. All came with auto trans or 3 or 4 speed trans on the floor or 3 speed in the tree / steering column.
|
| Question From:
george
2011-12-03
1968 Ford Galaxie Conv.
| Question:
Rebuilding a 390 for a 1968 Galaxie. Do the tabs on the bearings of the rods go to the inside or the outside.
Response(s)
|
| Question From:
Josh
2011-12-03
1965 Galaxie 500
| Question:
1965 Galaxie 500 with 390 CID V-8. What does the CID stand for? Did all the 65's come with a spotlight / Mirror like the one I am selling on eBay?
Response(s)
Cubic Inch Displacement. Spotlights were typically dealer added items. No not all 65's had them.
|
| Question From:
Matt
2011-12-02
Galaxie 500
| Question:
Working on a little project for Mom & Dad: Need to know the spacing between the Galaxie 500 letters as it appears on the rear quarterpanel. Also the usual thickness of the quarter panel steel. Much thanks!
Response(s)
|
| Question From:
john
2011-12-02
1964 galaxie 500
| Question:
I have purchased new filler boards and rear seat divider for 64 Galaxie. Any place to get instructions for installation?
Response(s)
|
| Question From:
Harry
2011-12-01
1967 Galaxie 500 XL
| Question:
No dash lights, horn, or tail/brake lights. Factory manual says it is a fuse located in or near the headlight switch. HOW DO YOU GET THE HEADLIGHT SWITCH OUT? Where is this mysterious fuse? Have the front of the dash disassembled but no access from there. Bottom access is blocked by a/c ductwork. Any suggestions?
Response(s)
you will have to reach up under the dash and feel for the switch then feel for the button on the top of the switch . once ytou have found it then press the button down and pull the headlight knob uot of the dash once you have the knob out then you will need to ues a screwdriver to remove the bezzel turning counter clockwise while holding the switch once you have the bezzel out then the switch will pull out and you can see the fuse . putting it back is just the opposit of the removal
|
| Question From:
frank klucaric
2011-12-01
1968 LTD vin 8w62q124686
| Question:
How many 1968 LTDs were built with the 428 engine?
Response(s)
thousands
|
| Question From:
Al Lloyd
2011-11-30
1961 Ford Galaxie Sunliner
| Question:
I need the correct color red paint in spray cans for the metal interior parts. Have looked all over cannot find yet I see pictures of newly restored cars with the correct color. Any help will be appreciated.
Response(s)
|
| Question From:
stuart
2011-11-30
1966 Ford Galaxie 2 dr. fastback
| Question:
Does anyone know of any vendors that produce any exterior trim parts for a 66 Galaxie? Also car I bought came with buckets, console and backseat of another car. Originally had bench. As far as interchange of seats go, anyone know if seats can be swapped with any other model?
Response(s)
Hi, Stuart. You can check out dearbornclassics.com, or macsautoparts.com. They might have a few of the trim parts you need, but the selection is limited. As a fellow 66 Galaxie owner, I can tell you from experience, that trim parts are just hard to come by, other than small bits and pieces. If your buckets and console are from a 65/66 Galaxie, hang on to 'em! They're equally tough to find. Good luck!
Hi, Stuart. You can check out dearbornclassics.com, or macsautoparts.com. They might have a few of the trim parts you need, but the selection is limited. As a fellow 66 Galaxie owner, I can tell you from experience, that trim parts are just hard to come by, other than small bits and pieces. If your buckets and console are from a 65/66 Galaxie, hang on to 'em! They're equally tough to find. Good luck!
|
| Question From:
steve francis
2011-11-29
1965 Galaxie convertible
| Question:
How many 1965 Galaxie convertibles where built with big block and 4-speed
Response(s)
No 100% certain way to know, Ford did not keep those kind of detailed production figures (engine-transmission combinations). But knowing Ford, probably not a bunch.
|
| Question From:
Daniel Olsen
2011-11-28
1970 Ford Ltd
| Question:
Are body mounts available for a 1970 Ford full size. My son has one and it leans to the right side. mounts are old and falling apart
Response(s)
dearborn classics or mac's auto carries motor mounts.
|
| Question From:
Kip
2011-11-27
1968 Galaxie 500 COnv
| Question:
Restoring a 68 Galaxie 500 conv. Frame is severly rusted, is there somewhere that manufactures new ones, or will a 67 frame match up?
Response(s)
Kip: The frame from 1967 and 1968 are the same basic car. Just depends on convert compared to hardtop cars. Convertibles have a crossmember to add lost weight from the cloth top. You can check with MAC Auto in NYC or Dearborn Classics. they may be able to help.
|
| Question From:
eddie godsey
2011-11-26
1961 ford fairlane
| Question:
Can I put a 289 hp with a fmx trans in a 1961 Ford Fairlane that came with a 223 cubic inch 6 cylinder without doing any cutting or welding?
Response(s)
Eddie, your 1961 Ford Fairlane is really a Galaxie and the last year the Fairlane is a fullsized car. The 289 should bolt to the FMX, but make sure its the 3 speed auto / CruisOmatic which should have the green dot drive for second gear. You may need to swap out the bell housing from a 289 since the main V8 in 1961 was the 292 Y block or the 352 and the 390. The chassis from 1960 to 1964 is the same basic car but the trans mount for the standard 6 may need to be moved and you might find the driveshaft is to long or to short. You can pretty much bolt any Ford V8 into the spot but the trans mount will be different for the V8 setup. Best thing to do is find a donor car, it can be a wagon, a 4 door, any model Galaxie with a V8 from 1961 to 1964, 1963 1963 will have 289, 352, 390.
|
| Question From:
Ina
2011-11-25
1965 Galaxie 500 xl
| Question:
My husband has a 65 Galaxie 500xl. There was a sign we had found in the car. It was a banner type paper printed sign that read “Need help” “send for gas” “out of gas” Or something similar along these lines. My husband has since lost the paper, and we have asked EVERYWHERE if they have ever heard of this “help” sign that came with the car. Wanted to throw it out there and see if anyone has seen or heard of this sign. I am interested in purchasing an original one if someone can send me in the right direction.
If you have any tips or information for me, please email me at kaarinasimpson@gmail.com
Sincerly wife on a mission, Kaarina
Response(s)
Ina, what you refer to came in the Ford owners manual for the later 1960 models Fords. I have a few in the later 60 and early 70's models, it was probably added by someone who had a later year Galaxie or Ford. It is standard issue by Ford Motor Company, it should say FMC or something on the paper. Contact Dearborn Classics they may have some.
|
| Question From:
david grimes
2011-11-25
1967 galaxie 500 xl fastback two door
| Question:
How do I replace my head liner in my 67 Galaxie XL 500 hood?
Response(s)
|
| Question From:
Marty
2011-11-21
63 galaxie convert
| Question:
Any idea how to get all the body trim to look new?
Response(s)
|
| Question From:
Marty
2011-11-21
1963 Galaxie 500 convert
| Question:
Can I run 15"x6" rims with out any head aches?
Response(s)
Marty, the 1963 Galaxie came optional with 15 inch rims. Many run 15x7 and bigger in the rear and run 14x7 in the front to get that rake look. The real thing you have to watch is to make sure you do not run to tall of a tire, this will change the speedo and gear ratio. It can be done and you can really stuff the rear with some wide tires. I run 60 series on the rear of my 60 and 64 Galaxies.
You will be find with 15x6 many run 15 in the rear and 14 in the front.
|
| Question From:
Ishmael Arellano
2011-11-21
1964 Thunderbird 390 Engine
| Question:
What vehicles are there that has the same lug pattern for wheels on a 1964 Ford Thunderbird whether 15 in. or 14 in.?
Response(s)
All passenger car wheels from 1957 to 1974 should fit your T-Bird, 14 and 15 inch wheels, Van and truck rims have a different bolt pattern.
|
| Question From:
Joe W
2011-11-20
1970 galaxie XL
| Question:
Long story short...1970 XL rear ended a van and I need a whole new front end. Any ideas where I can find parts?
Response(s)
I know where either a 69 or 70 is in a salvage yard. I have a few pictures because it is interesting looking. I can send them to you to verify the year.
|
| Question From:
JAIME
2011-11-20
1968 Ford Galaxie
| Question:
My brake pedal on my 1968 Ford Galaxie is hard and when I push the brakes it doesn't stop right away.
Response(s)
It sounds like the master cylinder is going out.
|
| Question From:
Andrew Hilsman
2011-11-19
1963 1/2 Galaxie 500
| Question:
I need a passengers side rear quater for my 63 1/2 Galaxie 500 is there anyone who make a full quater pannel?
Response(s)
You should be able to find those through MAC Auto in NY or Denise Carpenter.
|
| Question From:
Jeff
2011-11-16
69 Ford Galaxie
| Question:
Have a 69 Galaxie that I'm putting a universal wiring harness in so I need a complete wiring diagram of the original wiring in the vehicle. Any help would be greatly appreacieated.
Response(s)
www.classiccarwiring.com These guys are great!!
|
| Question From:
Jim
2011-11-16
1963 Galaxie 500XL 2 door hardtop
| Question:
Have been looking for a 63 Galaxie transmission 3 speed floor linkage. Have any ideas where to find it?
Response(s)
Check with Hurst and any other aftermarket supplier. New models can still be purchased.
|
| Question From:
F. Johnson
2011-11-16
1963 Ford Galaxie
| Question:
Looking for info on mirror placement. My 63 Galaxie (not 500 or XL), did not come with side view mirrors. I am adding them. Question is what determined the style and placement of mirrors back then. I've seen at least 3 different styles mounted on doors and fenders and vice versa.
Response(s)
|
| Question From:
Scott
2011-11-16
1964 Galaxie 500 XL
| Question:
Hello, I have a 1964 Galaxie 500 Xl Convertible. The car starts, idles great and runs like a champ. However from time to time the inline fuel filter appears to run empty. When this happens it spurts fuel in to the filter eractically and the engine will sometimes stall when a load is put on it. I have changed both fuel filters. Help please
Scott
Response(s)
It sounds like a fuel pump going out,mine was doing same thing and then it went out,I hope this helps.
|
| Question From:
Ray
2011-11-15
1966 Galaxie 500 Convertable
| Question:
Does anyone know if the entire dashboard comes out in one piece, like many other vehicles, on a 1966 Galaxie? I have the shop manual although it does not say. Some cars have two or three bolts on each side allowing the entire dash to come out all at one time.
Response(s)
Yes, you can remove the entire dash. I just took mine out of my 65. It is pretty easy to remove just be sure to mark all the electrical connections and bulb placement.
|
| Question From:
jw rushing
2011-11-14
1963 Ford Galaxie
| Question:
How do I remove stuck front brake drums on 1963 Ford Galaxie? I can not get them off any way, thanks.
Response(s)
Have you backed the self adjuster off, so the brake shoes pull away from the drum walls?
|
| Question From:
Keith
2011-11-11
1963 Galaxie Conv
| Question:
How in the blazes does the lense come off of the bucket of a 63 Galaxie tail light to replace the bulb? The backup light is in the center and can't figure out how to disconnect the wire to remove the lens.
Response(s)
|
| Question From:
dennis kindrick
2011-11-11
1967 ford galaxie 500 2door
| Question:
I have a 1967 Ford Galaxie 2dr with no windsheild or hood. I know where I can get, before its scraped, a 1968 Ford Galaxie 2dr. Will the windshield and hood fit? What about front A arms? My 67 is gone left side.
Response(s)
I believe the windshield is the same. The hood is different. The control arms will fit also and most likely the 68 will have disc brakes. I would be interested in the rest of the 68 if it is close to Memphis area.
|
| Question From:
Deloyd Swarts
2011-11-10
1966 Ford Galaxie 500 Convertible
| Question:
I am looking for the chrome that goes around the fenders.
Response(s)
I have a 66 conv. I am taking all the chrome off. If you give me specifics, we can work out a deal
e:mail me at dswarts37@yahoo.com
I have found some of the chrome but may need some you have. I am looking for rear quarter panels. I thought I had some but they were rusted out. If you have some I am interested in seeing pictures.
|
| Question From:
larry mehegan
2011-11-08
1963.5 R code Galaxie 500 Fastback
| Question:
How many gas tank sender unit seals should there be on a 63 Galaxie? Mine had 2 when I removed the unit from the tank. They were back to back to each other. One was a slightly smaller section than the other, although very similar in diameter.
Response(s)
Normally there is one, but it may have leaked or who knows what. Replace it with a single gasket and some gasket sealant that is oblivious to fuel.
|
| Question From:
Richard Dawson
2011-11-08
1966 Galaxie 4dr HT 352
| Question:
My son and I are restoring his recently purchased Galaxie and are working on the engine. We gave the intake manifold a bath to clean it up for fresh engine paint. The engine now acts as if it is not getting fuel to the spark plugs. Is the intake filter ? - porous like material that sits directly below the carb replaceable - or is it even needed? Most intakes don't have this - do they? Can I buy a replacment? Is there a good way to clean it or is a replacement needed? Thanks in advance. Rich D.
Response(s)
You and your son should go back to playing with dolls. It sounds like you know nothing about cars.
I BELEVE YOU ARE REFERING TO THR SPACER PLATE IT HELPS INSULATE THE CARB FROM HEAT ALSO HAS A VACUMPORT RUNNING OUT THE BACK SIDE, IT MUST BE INSTALED CORECTLY OR YOU WILL HAVE A MAJOR VACM LEAK AS FOR THE CRACK ABOUT PLAYING WITH DOLLS FORGET HIM
buy a chiltons motormanual for appropiate years I picked one up at rumage sale for 3 bucks,will have specs and how to do info for your project
|
| Question From:
F. Johnson
2011-11-06
1963 Ford Galaxie Sedan 2dr
| Question:
Looking to install six belts in my 63 Galaxie sedan. It is my understanding that there are mounting locations for two in the front and none in the back. Where can I look for more information on this install. Is it even possible to put six belts in this car?
Response(s)
The 1963 Galaxie 500 did have optional rear seat belts and there should be bolt holes under the rear seat, you will need to pull the bottom of the back seat up, it just kind of pops out by lifting and pushing it backwoods. You might just find it has rear seat belts already, many people stuffed the rear belts down under the seats. If the belts are not there you should see bolt locations on the floor pan. Just remove the bottom rear seat first.
|
| Question From:
Carol Makowski
2011-11-05
Ford Galaxie 500 convertible 1968
| Question:
Where can I get a neutral safety switch for this car? 1968 Ford Galaxie 500 - 390 engine.
Response(s)
You can find them at Dearborn Classics, Mac Auto in NY. You can also find them at transmissions shops too, you have a C6 transmssion in that car.
|
| Question From:
John
2011-11-05
1963 Country Squire
| Question:
I have a 63 Galaxie Country Squire wagon that needs lower rear quarter panels and dog legs. Can you tell me where to find these repair panels, and are they the same panel dimensions as a 4 door? Thanks, John
Response(s)
Your dog legs for the 4 door sedan and wagon should be the same. You might find those at Mac Auto in NY or Dearborn Classics, or Dennis Carpenter. The doors for the 4 door sedan and wagon are the same except its a wagon.
|
| Question From:
Maury H
2011-11-04
1969 Galaxie 500
| Question:
I have a 1969 Galaxie with 390 engine, is it possible to add ac to it?
Response(s)
Maury, in 1969 Ford offered AC as optional equipment. You can either try and find a system in the junk yard or get a custom AC system from Classic Auto Air, which might be a better option in todays world. Your 1969 390 would have the same AC system on all full sized 1969 1970 Mercurys and Fords with the 390. So you could use all the brackets and mounts and compressors.
|
| Question From:
Oscar
2011-11-03
1966 Galaxie 500 Conv
| Question:
1966 Galaxie Conv. Where is the VIN plate? More than one VIN plate?
Response(s)
I own a 66 conv 6J65X------
The vin is in 4 places
1- in the engine bay r/h side tab on the firewall
2&3- underneath the quarter panels forward of the door hinges
4- on the data plate on the driver door. Keep in mind that if the door has been changed, the vin could be wrong at that location.
|
| Question From:
David Buck
2011-11-03
1960 Ranch Wagon
| Question:
I need a source for body/chassis mount rubber for a 60 Ranch Wagon. I have been told that the wagon rubber is different than the Galaxie. I have not found a supplier of '60 Galaxie rubber either.
Response(s)
The 1960 is a tough year since it was not the most popular. I would think the 1961 could be similar. Mac Auto in NY, Dennis Carpenter, Dearborn Classics. 1960 to 1964 is the same frame.
|
| Question From:
ken weydeck
2011-11-02
1967 galaxie convertible
| Question:
Where can I buy a frame for a 1967 or 68 Galaxie onvertible?
Response(s)
I will bet you can buy a frame from under another 67 or 68 Galaxie...all humor aside, check craigslist and ebay....or your local salvage yards.
|
| Question From:
kevin
2011-11-02
1970 Ford Galaxie 500
| Question:
How do you remove the gas tank on 1970 Ford Galaxie 500?
Response(s)
Remove the straps, sending unit wires, fuel lines, and filler tube/vent hose. Oh yeah... its a whole lot easier if the tank is nearly empty.
|
| Question From:
josh luallen
2011-11-01
1966 Ford Galaxie
| Question:
Where is a horn relay on a 1966 Ford Galaxie located?
Response(s)
|
| Question From:
Bob
2011-11-01
1966 Ford Galaxie 500
| Question:
I have a 66 Galaxie 500 and need to change the heater fan motor. How can I change it without removing the R/front fender
Response(s)
It is tough but can be done
1- remove hood, mark washer locations so you can install very close to original
2- remove r/h hood hinge, same thing mark it. you could skip this if you want
3- many tools and triple jointed elbow/wrist
|
| Question From:
Edward Berg
2011-11-01
Ford Galaxie 500 Xl
| Question:
Hi. Do any of you know how to adjust a manual window regulator on a 67 Galaxie? When I crank the windoe it does go up evenly (the left side of the window is a little bit higher than the right side so the window did not close completely. Thank for your answers. Regards E.B
Response(s)
Ed, you will need to remove the door panel and make an adjustment to the 2 bump stops that are on each window. They are out of adjustment and can easily be unbolted and realigned. Some have rubber on them that wears out. The only other reason this woould happen if the window is off the track which you would see with the door panel off. Good luck
|
| Question From:
brent
2011-10-31
1962 Ford Country squire
| Question:
Valve cover and air cleaner color for a 352 cubic inch is? I know the block and intake to be black. I have seen pale or powder blue (like Ford body color), gold and argent silver but I thought those colors were designated to 390's and 406's and Ford blue yet thought that came later. The correct color and where to purchase would be appreciated. Thanks.
Response(s)
Your 1962 Galaxie 500 with a 352 would be a black block and blue valve covers and blue air cleaner, you can use the blue that is known as Ford blue, Dearborn Classics would carry this color. Ford engines are black up to 1964, in 1965 they go to the all Ford blue. Another area to watch is the front valance between the bumper and grille should be silver or gray, many people paint this body color on many year cars, it is silver or gray to blend in with the chrome.
|
| Question From:
John
2011-10-31
1964 Galaxie 500 XL
| Question:
I have a 1964 Galaxie 500 XL which isn't getting any fuel to the carburetor. I went ahead and changed the fuel pump out. Now I'm not getting any fuel to the pump. I attempted to blow air into my tank in order to prime the pump but am only getting a trickle through to the pump. Any ideas?
Response(s)
I installed my hoses backward on the fuel pump, took me a few days to figure out the problem, Roll Tide Tom-Ala
|
| Question From:
CJ Ford
2011-10-31
1966 Ford Galaxie 500
| Question:
Where can I get a frame for a '66 Galaxie 500 or what can retrofit one. I have a virtually spotless
one, but frame rot.
Response(s)
|
| Question From:
roy dwyer
2011-10-29
1964 Galaxie 500 xl
| Question:
I am trying to find motor numbers on my 1964 Ford. I want to see if it is a 390 or 352. Thanks Roy Dwyer.
Response(s)
These blocks are the same
The only way to know for sure is to take measurements.
Pull a cylinder head
4.050 inch bore is a 390 cid
remember to measure at the ridge since this is the original bore
I recently purchased a 1964 Galaxie 500 & I typed the vin# on vin decoder site & found out mine was made in Norfolk,Va. & has a 352.
|
| Question From:
Michael O. Robertson
2011-10-28
1965 Galaxie 500
| Question:
I'm switching my 65 Galaxie from column to console shift (cruise-o-matic). I have the shifter but will either have to find or fabricate the linkage to the trans. Can anyone supply a photo or an exploded diagram to aid me in my quest, and supply any other pertinent info. Thanks for any help.
Response(s)
|
| Question From:
tim
2011-10-27
1965 galaxie 500, convertible
| Question:
Hi, just bought a 65 conv. 289 w/ps, pwr brks. Brakes work well, but barely touch pedal to engage them-literally no travel, so brake lights don't readily light up. How do I get more pedal travel? Or, is it a fluid prob? mc is single bowl.
Response(s)
|
| Question From:
David
2011-10-27
1966 Ford Galaxie
| Question:
How can I easily add/convert to power brakes?
Response(s)
Most 68 Galaxies and LTDs had disc brakes and they work good. I would assume the spindles would bolt right up. I have also used 71 LTD spindles on a 64 using the right ball joints and they worked really good. Just make sure the ball joints have the right taper angle for the spindle and bolt up correctly to the control arms. You have to use at least 15" rims with either of these.
We used 1969 discs have had no trouble for over 10years. Was very easy job.
We used 1969 discs have had no trouble for over 10years. Was very easy job.
|
| Question From:
Abraham
2011-10-27
Ford Galaxie 500?
| Question:
I looking at buying a 63 Galaxie 500 Conv. from a guy and you look at the car and see that it's a 500 by the emblems and the interior but the guy he bought it from said he took off the Vin/Data tag when he painted it and lost it. The title the man gave him has a VIN number of 3G69Z183879 and I looked it up and thats a title for a 500XL Conv and not a 500. The VIN tag under the hood on top of the firewall by the hinge on the passenger side had a metal plate that look like it was tack welded over the top of it. He broke that off but water had got in between and rusted it so bad you can't make out the numbers. My question is this. Is there anywhere else on the car where I can find the VIN number like on the frame or anywhere else?
Response(s)
I would either talk him down or run like hell.
|
| Question From:
Tim Cooper
2011-10-25
1968 Ford Galaxie 500 Two Door Hardtop
| Question:
Does 1968 Ford Galaxie convertible door panels fit the 2 door hard top? I know they don't match but will they fit the door.
Response(s)
Tim, the 2 door hardtop and the 2 door convertible share the same doors and the panels will swap over. Both cars share the same side glass also.
|
| Question From:
Al Vesel
2011-10-25
1967 Ford Galaxie 500 2 dr convertible
| Question:
Is there a difference between a 2 door hardtop door/window and a convertible door/window? I just purchased a 1967 Ford Galaxie 500 convertible. The top when up had gaps where you could see inside the car. I took it to a reputable place to have a top put on. They looked at it and told me that the cables were missing and once they put a new top on, they will install new cables and that will bring it tight and you won't see inside the car anymore when top was up. They called me today and said there was an issue and that once the new top was installedthere was still a gap, but not as much where you could see inside. He said for me to come and take a look at it and he thought that the car had maybe a 2 door hartop window or door in it, when it should be a convertible door or window. I have to go today, 1025-2011 and pick it up. I haven't paid for it all. They charged me $1,500.00 for the top and back plastic window and installation. I thought that was high especially when it looks like the tops only run around $300.00 new, even from Dearborn. I don't want to pay $1,500.00 for a new top if it looks almost the same as the other one. That is the only reason I had them put a new top on is because of that gap space between the top and the top of the window/door. The top that was on it prior wasn't that bad, just a few places that were stitched and the cable ends were broke so you couldn't draw the cable together to tighten it. I think he's giving me a line of bull when he said it's because of the wrong door or window on the car.
Response(s)
|
| Question From:
Jim K.
2011-10-24
1969 Galaxie Convertible
| Question:
Today I was told of a '69 Galaxie convertible w/ a 390 that is for sale. Don't know much about it other than it has 36k original miles, but has been sitting for more than 30 years. Not even sure if it runs. Owner is asking $1,500. Reasonable? Thanks
Response(s)
1500 for a 69 galaxie is very reasonable depending on what you plan to do with it. Alot of people get them to restore, so if you want to put more money to bring it to life its well worth it.
|
| Question From:
Jim Parks
2011-10-24
69 Galaxie Country Sedan
| Question:
My customer has a 1969 Ford Galaxie Country Sedan and needs the following:
letter "R" on hood from FO R D
Fuel tank sending unit
1 std hub cap.
Please advise. Thank you.
Response(s)
|
| Question From:
Dave Fleming
2011-10-24
1964 Galaxie 500 convertible
| Question:
We are presently restoring a 1964 Galaxie convertible and have a bad wiring harness from the dash to the tailights. The fuse block is also very bad. Is there anyone that sells the wiring harness with the fuse block? We have already checked with Dearborn and they could not help.
Response(s)
you will have to use an aftermarket harness . no one makes a factory replacement harness .
|
| Question From:
Gregory Altilio
2011-10-24
1969 Ford Galaxie XL GT
| Question:
Do you know the paint codes for all available colors for a 1969 Ford Galaxie XL GT? Do you know a supplier for the C-stripe for this car?
Response(s)
|
| Question From:
Darlene Memmo
2011-10-23
1968 Ford Galaxie
| Question:
My Father-in-law is ailing and we would like to restore his 1968 Ford Galaxie. My question is will the same windshield fit a 2 or 4 door Galaxie?
Response(s)
yes the are the same
|
| Question From:
Tyrone
2011-10-23
1967 Galaxie 500 sedan
| Question:
What car can I swap out my 1967 Ford Galaxie 500 4 door sedan drum brakes to disc?
Response(s)
thundertird , ltd , torino will work.
I have a 63 conv that has 4 wheel disc from an explorer or expedition. Not certain which one.
|
| Question From:
Bart Hannah
2011-10-22
1962 Galaxie 500
| Question:
I have 1962 Galaxie 500. Where can you get front and patterns for a rebuild?
Response(s)
front what ? patterns for ?
|
| Question From:
jim abriel
2011-10-21
1966 Galaxie Country Squire
| Question:
Need to know the routing of the heater defrost cable on my 66 Galaxie wagon. I only have air coming out the air condition vents.
Response(s)
|
| Question From:
Tom
2011-10-21
1966 galaxie 500
| Question:
I want to remove the padded part of my dash to send it to justdashes to be redone. How do i remove it? It feels like it may be glued to the metal of the dash. Any ideas?
Response(s)
There are screws on outer edge,and clamps near front wind screen that hold chrome strip and dash in place
you must go deep under dash with needle nose pliers and sweeze the center of clamps to release dash,and GOOD LUCK !!!
There are screws on outer edge,and clamps near front wind screen that hold chrome strip and dash in place
you must go deep under dash with needle nose pliers and sweeze the center of clamps to release dash,and GOOD LUCK !!!
|
| Question From:
Boyd McPherson
2011-10-20
1968 Ford Galaxie 500 XL
| Question:
I'm looking at purchasing a 1968 Galaxie 500XL convt. and I had the seller send me a picture of the warranty tag/plate from the driver's door. Unfortunatly the door must have been replaced at some time because the tag says the car should be a hardtop and a 302 vs 390 that is in the car. Where else on the car can I find a tag with the same information as on the door warranty tag/plate?
Response(s)
I have a 1967 and the vin is under the left front finder. The only bad thing is you have 2 remove the finder
On a 65/66, there is a metal tab on top of the firewall. Look on the right side above the airbox near the hinge.
|
| Question From:
Roy Smith
2011-10-19
1964 Ford Galaxie 500XL 2 door
| Question:
I bought a 1964 Ford Galaxie 500xl 390 4 speed. It has round Ford mirrors with Ford emblem, but they are mounted on the front fenders. Is this right or should they be on the doors?
Response(s)
they were mounted on the fender
they should be mounted on the doors not the fenders. I own a 64-500. mine has a single mirror interior adjust knob. My friend also owns a 500 xl and his mirror is on the door also. all photos i have seen have them on the doors and they are usually rectangular or square with no mirror on passanger side.
I have a 64 bought from the original owner and they are on the door
either location,
|
| Question From:
Doug Bethune
2011-10-18
1967 Galaxie 500 XL 2Dr. Fastback
| Question:
I am about to install a new rear windshield in my 1967 Galaxie. I have a new seal I purchased. I am at a loss in how the seal seals the water from running into the groove in the rubber that the glass fits in. Do I glue the rubber to the glass with weatherstrip adhesive? When putting the glass and rubber in the recess do I put a windshield sealer kit under it and over it? Any advice would be appreciated.
Response(s)
|
| Question From:
ken
2011-10-18
62 63 hardtop Galaxie
| Question:
I have a 62 or 63 Galaxie hardtop body only from the friewall back no glass or door. RUST FREE zero rust or bondo. any interest and what might it be worth. Also a few boxes of parts window cranks heater motor not sure whats there.
Response(s)
Ken.. There is a pretty big difference between 1962 and 1963. The 63 64 are more the same than the 62 63. A 1962 or 1963 Hardtop would be a square roof and not the fastback style. The 1962 will have a rounded rear quarter where the 1963 has large round taillight housing molded right into the rear quarters. Best thing to do is a yahoo search on the image page to find which one you have. The 62 square roof is not as popular as the 63 so knowing the years is important. If its a rolling chassis that also adds to it. The 62 and 63 would not have much interchangeable body parts, the 61 and 62 share much as do the 63 and 64. Best guess would be about $200 depending on which and what parts, could be up too $1,500.00 but might be pushing it. All depends whats there.
Just do a Google search for Ford Vin Decoder then put in your Vin # and it will tell you the year and other info about the car.
A good Vin decoder is called, Decode This do a google search on it and put in your Vin#
|
| Question From:
dan king
2011-10-17
1968 Ford Galaxie XL Convertible
| Question:
Who rebuilds the '68 Galaxie XL convertible master window switches, please? All windows now are lubed and go up and down smoothly, but only when 12v is applied directly to the motors. A new relay makes no difference. The switch is the last piece in the puzzle. Any experience out there? Thanks, Dan in Austin
Response(s)
|
| Question From:
tim yeargle
2011-10-17
1966 Galaxie 500
| Question:
My girlfriend has a 66 4-door Galaxie, the outside window sweeps are rubber. They are so weathered they are hard like plastic and brittle, broken in several spots, rain water flows in easily. All I've seen are 2-door sweeps, that I would have to modify and would be costly.
Response(s)
try dearbornclassics.com they will have what you need
|
| Question From:
cameron lyman
2011-10-16
1964 Galaxie Fastback 289
| Question:
I have a 64' fastback that I'm planing a frame swap on and I would like to know if a 64'convertible X frame would fit under a fastback? I would like to go with the x frame for more support and I've tracked down a conv. car in my area for a good price, I just need to know if it will work before I buy.
Response(s)
The only real difference between the hardtop and the convertible should be the convertible crossmember. You might want to see how bad the frame is on the convertible before actually making the switch. You might find your best bet might be to cut out the X member and weld to your original frame. Either is going to be a lot of work and I think the best condition frame wins but I also like knowing the original frmae is there if you want matching numbers. The convertible must be pretty rough if its a parts car and they do rust and rott pretty good compared to the hardtop. I guess it all comes down to money and time.
|
| Question From:
roger foss
2011-10-15
1963 Galaxie 500 xl conv 390 /no a/c
| Question:
What should be the bumper heights from the road for a proper suspension?
Response(s)
|
| Question From:
Frank
2011-10-15
1967 Ford Galaxie 500
| Question:
I have a 1967 Galaxie 500, I was told that it was 1 of a few built with a 410 my VIN shows 390 how can I find out? VIN # 7U55H124073
Response(s)
there were no galaxies built with the 410 engine . the 410 was only uesd in the mercury cars . your engine has been a non factory install
the only true way to find out if it is a 410 cid is to pull ahead and measure the bore and stroke . the 390 is 4.05 bore and 3.78 stroke . the 410 is 4.05 bore and 4.98 stroke
to measure the stroke you will need to move the piston all the way down to the bottom of the cylinder and measure the depth then move it all the way up to the top of the stroke and measure the distance from the top of the piston to the block lip . then take the differnces between the two measurements and that will be the stroke
I have checked that. It has a 428 crank witch is the crank thay use in the 410. Thear is no engine # but a c on the back of the block. It is a 410. What I want 2 Know is how I can find out If it was bilt that way
Going by the Vin # on your car 7=1967,U=Assembly Plant Louisville,KY 55=Galaxie 500 Fastback, H=390cid 270hp 2BBL carb with 9.5:1 compresion and the 124073 is the serial # that means your car was the 24073 car made. So if you have a 410 in it now it was added latter because your car left the factory with a 390.
|
| Question From:
Joe Lamm
2011-10-14
1966 Galaxie 500 2 door ht
| Question:
Replacing incorrect bucket seats with bench seat (as original). I obtained a bench seat complete with adjuster. when I connect the adjuster to the seat tracks on both ends of the seat it is approx. 4 inches too long (even when adjusted to its shorted length). If it WERE short enough to take up the slack with the adjusting mechanism, it would then (upon installation of the seat) hit the drive shaft hump before the seat tracks hit the floor. what am I missing here??
Response(s)
|
| Question From:
bob olah
2011-10-13
1962 ford galaxie
| Question:
I have a 1962 Ford Galaxie 406 motor drum brakes
all around need a new brake booster orginal a must
car is totaly restored.
Response(s)
dearborn classics .com or gregg donahue will have one
|
| Question From:
H l Smith
2011-10-12
1967 Ford Galaxie 500 cvc
| Question:
How to install power windows in a non powered window 1967 Galaxie cvc?
Response(s)
|
| Question From:
mike
2011-10-11
1967 Galaxie 500 fastback
| Question:
I recently purchased a 67 Galaxy fastback. The reverse lights don't work. How do I get to the reverse light? And is there a fuse in line for them?
Response(s)
Reverse lights run thru the neutral safety switch. Switch could out of adjustment. A owners manual should show you the fuses. Or better get a service manual or wiring diagram.
Try this link: http://www.hotrodders.com/forum/1968-ford-galaxie-133326.html
|
| Question From:
ralph palo
2011-10-10
1964 Ford Fairlane Two Door
| Question:
What model Ford exterior driver side door handles with push buttons will fit a 1964 Ford Fairlane?
Response(s)
1963 and 1964 will interghange
The door handles for a 2 door and a 4 door are the same on most models. You can you a 4 door set and the handles from the right side should fit the front or back door, just left or right is different. I have used wagons and 4 doors cars to get extra door handles at junk yards for years. Also remember the Mercury Comet has probably got the same handles. I beleive these are reproduced.
|
| Question From:
Tim
2011-10-09
1968 Ford Galaxie 500 2 door
| Question:
Where can I find new body to frame bushing and bolts?
Response(s)
I recently got the bushings from AutoKrafters, but they only sell the rubber parts. You have to use the old steel inserts.
|
| Question From:
Saul
2011-10-06
1965 Ford Galaxie 2 door
| Question:
Do the fenders and windshield from a 1966 Ford Galaxie 2 door, fit on a 1965 Ford Galaxie 2 door?
Response(s)
yes the 65 and 66 parts will interchange but not 67 or later
63-74 Interchange Manual says they are different. Can Anyone explain. They look close but is the body design different?
I own a 66 Gal conv.
Yes, they will probably fit. However, they physically look different. Google images of both to see the difference. 65 is more squared off around the headlights.
They are actually different because the 1965 is a square style at the corner of the fenders where the 1966 is more rounded. the fenders might lineup but they are not the same fenders.
|
| Question From:
Johnnie David
2011-10-06
1965 Ford Galaxie convertible
| Question:
How to remove front seat from 1965 convertible Galaxie, bench with flop seats.?
Response(s)
you have to climb under the car and undo the 8 nuts. i ran into that problem myself.
|
| Question From:
Norman Martinez
2011-10-06
1964 Ford Galaxie 500XL
| Question:
I have a 1964 Ford Galaxie 500 XL with a 352. I need to buy a new power steering pump. I need to know what the difference is in a rear mount and a front mount power steering pump. How can you tell the difference?
Response(s)
I have never heard of a rear or front pump, there is 2 different styles or setups for 1964 big block cars depending in most cases if you have AC or not. AC cars have the reservoir mounted on the drivers side inner fender and most non AC cars have the reservoir mounted on top of the pump. The pumps are the same just one bolts the power steering fluid reservoir on top and another on the inner fender. Best thing to do is remove the pump and take it to the parts house if possible so you can compare. 390 / 352 pumps are the same ones. I owm a 1964 XL with a 352.
|
| Question From:
Chris
2011-10-04
Ford Galaxie 500
| Question:
I recently purchased a 65 Galaxie 500 convertible. The top is stuck in the down position, motor makes normal noise but will not move top. How do I access motor when top is down?
Response(s)
check the fluid levels then the pump to see if the pump is working then check the hydrolic cylanders
first remove back seat motors in center under seats.when the seats out check fluid and check lines there plastic and some leak .the lines can be costly .dearborn classic
|
| Question From:
59Geranium
2011-10-04
1959 Ford Galaxie 2 Dr. Hardtop
| Question:
Does anyone know what size nuts are used on the motor mount studs on a 1959 Ford Galaxie 2 Dr. Hardtop? I can't find any common sizes to fit!
Response(s)
|
| Question From:
Don Myrtle
2011-10-04
1963 Ford Galaxie 500XL Conv
| Question:
I have a 1963 Ford Galaxie 500XL Conv, I would like to know where to install the horns? Looks like the harness is close to the radiator support,
but I don't see any bolt holes that would let me
to install them. Any help would be grateful.
Response(s)
they go on the radiator core suport on the driver side just behind the inner headlight right beside the radiator
|
| Question From:
ZOhar Avney
2011-10-04
1966 Galaxie
| Question:
I started a restoration on my car years ago and lost motivation. I need to put it back together. Any idea of a checklist or game plan. I don't know where to start.
Response(s)
you will need to start with the body work and paint, then the drive train, then wiring ,then body panels that have been removed and any glass thats been taken out .then the interior thats out of the car
|
| Question From:
Zohar Avney
2011-10-04
1966 Galaxie Conv with 500XL front end
| Question:
I took my hazard/flasher out years ago and can not find how to reinstall the wiring. I do have several elec diagrams. Any help as to where to start.
Response(s)
|
| Question From:
Mark Bell
2011-10-02
1968 Ford Galaxie 500
| Question:
I am trying to take the gas tank off of the 1968 Galaxie 500, but am having trouble getting the pipe disconnected from the place where the gas goes in.
Response(s)
|
| Question From:
chad
2011-10-01
1967 Ford Galaxie 500 4 door hardtop
| Question:
What would the wiring on a 1967 Ford Galaxie 500 be for the alternator and regulator? I mean what colors mean what and what is the yellow wire coming from the regulator that has a conection like it plugs into something else but I dont have anything to plug into it? Also I have a solid black wire coming from my wiring harness that runs around to the dash area but it comes out to nothing when it gets to the selinoid it is like someone cut it but I am not sure where it goes. I can't find out where they cut it from my alternator light is on on the dash and it is only charging about 10 volts. Thanks cr
Response(s)
|
| Question From:
Bill Drake
2011-10-01
1963 Galaxie 500
| Question:
1963 Galaxie 500; 352; two barrel. New [mechanical] fuel pump and filter, reworked carburetor. Car starts and runs better than it did 55,000 miles ago when it was new. PROBLEM: When car sits a week or so it will not start w/o a little priming through the air filter/carb. Have checked for external leaks and tightened line connects. Any ideas.
Response(s)
bad carb. try a different carb should fix the problem
It is actually a common problem with todays gas because it evaporates very quickly. In my 1964 Galaxie I run Mobil, or Shell, Chevron Premium fuel. You are probably running regular which should be ok, just the gas evaporates very quickly these days.
|
| Question From:
Keith
2011-10-01
1963 Galaxie 500 convertible
| Question:
I can not find arms and brackets for the sun visors. Would any other car or year work instead? Where can I get replacement arms and brackets? The car is missing everything.
Response(s)
have you ecklers,(dearborn classics)
dennis carpenter has them in stock
Good luck. Not one vendor I called had a set for my 63 conv. The brackets for the conv are unique for that year and nothing else will fit. Nobody makes replacement parts for that yet. I got lucky and found a set in a box in my trunk. Call stan the ford man near seattle wa, he did have a set, but expect big money. (supply and demand)
|
| Question From:
trey weferling
2011-09-30
1964 Galaxie 500 2 door 390 4 barrel
| Question:
Does the 1964 Ford Galaxie have a drain plug for its gas tank?
Response(s)
no . if you want to drain the tank you will need to unhook the fuel line and gauge wire from the front of the tank then remove the straps and lower the tank from the car then drain it from the fill tube.
Or leave it in the car and siphon the gas out with a garden hose into a large bucket.
I presently havre ther tank out of my 64 and it has a small drain plug way up in the corner opposite the filler ??
|
| Question From:
niresh
2011-09-30
1965 Galaxie 500 ltd
| Question:
Hi. I recently replaced the 390 engine with a 351 drive train on my '65 Galaxie. Problem is that when I press on the brakes, the car engine dies off. It just appears to choke and switches off. I have repalced the brake booster, overhauled the carb, changed the plug leads, and still have the same issue. Please suggest. I want to fix this on my own, so a mech shop is not an option.
Response(s)
On my 68, I had a master cylinder start leaking out of the rear when you depressed the brakes and it was sucking brake fluid into the engine. It also ruined the diaphram in the booster. Check if the back is wet. Good luck.
A friend had had this problem when he switched to a 1970 390 in his 64 Country Sedan. The problem was in the intake manifold because of all the vaccum lines from the 1970. We had to switch to an early 64 intake to get it to work correctly. I would suggest you check your vacuum lines to make sure you are feeding off the right one, you maybe taking vacuum away from the engine and you should have a vacuum line going to the trans also.
|
| Question From:
scott thomas
2011-09-28
1971 Ford Galaxie 500
| Question:
I have a 1971 Ford Galaxie 500 that is set up for small block and I want to put a big block 460 in it what would I have to change and were can I get what I need.
Response(s)
you will need to change motor mounts , trans and mount ,cross member also the radiator . you can get the mounts from crites auto parts
sorry i ment crites preformance parts.com
The best thing to do if possible is to find a donor car. You could use a 1971 1972 Mercury Marquis, Monterey, Galaxie, LTD sedans or station wagons. You could even use a Lincoln Continental Sedan. All are full sized, of course the trick is to find a complete one. A donor car will provide you with the engine all the crossmembers and transmission along with driveshaft and any wiring you may need. Best bet maybe a junk yard. Takes some work but it can be done.
Thanks
|
| Question From:
Tom Ginn
2011-09-27
1963 Galaxie 500 xl convertible 260
| Question:
Need replacement brake line distribution block for front and rear. Old one is rusted out.
Response(s)
dearbornclassics.com try them if they dont have one try gregg donahue
|
| Question From:
George
2011-09-25
1966 Galaxie 4 door
| Question:
I have a 1966 Ford Galaxie 4 door it has some damage on the pass. rear door. I heard you can use 68 Ford Galaxie doors.
Response(s)
you will need to use 65 or 66 doors . 68 doors willnot work
You can also use 1966 station wagon doors if you have the sedan model. 1968 is very different.
|
| Question From:
James
2011-09-25
1967 Ford Galaxie
| Question:
I want to know where I can find a Ford Galaxie 4 barrel carb? Been looking for days now and so expensive if I'm not mistaken it's a 292 or something. Please help?
Response(s)
|
| Question From:
alicia
2011-09-24
1968 Ford Galaxie 500
| Question:
My bf is restoring a 1968 Galaxie 500 with a 429 engine. The starter was taken out and tested at an auto store and works, but when put back into the car it slowly turns and wont kick over.
Response(s)
replace the ground wire from the battery to the engine block. it is most likely swollen with corrosion and has high resistance. is it worse when the engine is hot? i would replace the positive wires as well
|
| Question From:
Kevin Vandrak
2011-09-23
1968 Galaxie 500 Fastback
| Question:
Anyone out there put headers on a '68 with a 390? How did they fit? I would like a set but don't want to have to hammer or saw! Thanks
Response(s)
The guys over at fordpowertrain.com made a set for my 67 LTD with a 390 and they fit perfectly. You might wanna give them a holler.
I have 2 68 LTDs with 390s. I used the short headers from fordpowertrain.com on the most recent and the Hooker SuperComps on the other one. The Hookers use a 2 piece pipe going to either 6 or 7 cylinder and they are 1.75" and long tubes. We got them in with the engine in the car, but it was a lot of twisting and trying.
|
| Question From:
Lewis Lingwood
2011-09-22
1963 Galaxie 500 4 door boxtop
| Question:
I have the ugly duckling. A 1963 Galaxie 500 4 door boxtop (no post). I've had it for many years. I was going to make it into a 406 sleeper. The roof rail seals are shot. Can't find any for this car. Anyone have an idea for a substitute? Thanks.
Response(s)
dearborn classics.com has them for the 4 door
|
| Question From:
Todd Hazard
2011-09-20
1963 Ford Galaxie 500 2door HT 352 2V HT
| Question:
Bought a '63 2-door hardtop as a driver. Discovered that the frame is just about rusted through, about in the middle of the car where the crossmember and body mount all converge. Doesn't look like we can get to it to repair without removing body. How big of a job is it to remove the body? Is it feasable to repair frame or should we be looking for a replacement frame? What years and models will work on our car?
Response(s)
you would be better off replacing the frame . you can use a 63 or a 64 frame
|
| Question From:
lindsay a. dobson
2011-09-20
Ford Galaxie 500 xl fastback coupe.
| Question:
Gentlemen, I have an original 1965 Ford Galaxie 500 xl fastback. The color is Rangoon Red. Where can I purchase this original color and how much of it will I need to purchase. Thanks! Lindsay Dobson.
Response(s)
you can purchase the paint from any automotive paint store and you will need one gallon of paint and reducer and clear and hardener .you should be able to buy it as a complete kit
|
| Question From:
Kris
2011-09-20
1966 Ford Galaxie 500
| Question:
Will the exterior door handles of a 4 door 1966 Galaxie 500 fit on a 2 door of the same make/model?
Response(s)
yes but you will need to use the front handles
|
| Question From:
Rusty
2011-09-19
1961 Mercury Meteor 800 2 door sedan
| Question:
I have a 1961 Mercury Meteor 800 2 dr sedan. It has power windows. My windows will not go up or down. I'm getting no power to the switches, and need to know where the power is coming from. Is their a fuse or a circut relay I'm not finding? any help would be great. I'm stumped.
Response(s)
you will need a wiring diagram to find the corect routing for the power wires your fuses are mounted to the headlight switch . you will need to remove the switch to see the fuses witch are the round glass type fuses
|
| Question From:
Jeffrey Zines
2011-09-19
1962 Ford Galaxie Sedan
| Question:
I have a 1962 Galaxie 2-door sedan. It is a bench seat car, however a previous owner put buckets in it. My question is, will bench seats from later Galaxies (65/66,etc) fit in a '62?
Response(s)
no they are a smaller seat than a 1961 - 1964 seat witch is what you will need to use if you are wanting to replace the buckets with a bench seat
|
| Question From:
reg menard
2011-09-19
1967 Ford Galaxie
| Question:
I am looking for vaccum diagram for a 67 ford galaxie with a 390.
Response(s)
|
| Question From:
Joe Lamm
2011-09-18
1966 Galaxie 500
| Question:
I own a '66 Galaxie 500. while researching my VIN number I have found the 3rd and 4th digits (66) to designate both Galaxie 500 "fastback", and Galaxie 500 Hardtop, depending on the web site. What is the difference...or all they both the same??
Response(s)
The 1966 Galaxie 500 2 door hardtop is the 2 door fastback. It can be referred as either. That was the only way the 2 door hardtop came in 1966 was as the fastback style and shares the same styling que as the convertible.
|
| Question From:
Troy Thomas
2011-09-18
!966 Ford LTD 4 door hard top
| Question:
We are restoring a 1966 Ford LTD 4 door hardtop. There is a vent along the out side of the rear window that has two drains that run through the car behind the rear seat and exit under the car. The rubber drains have deteriorated. Where can I find replacements?
Response(s)
Its called Silent Flo. Id love to repair mine to see if it really works. I pulled the knob out and I felt a slight change in rpm from the vaccum canister opening,but my hoses are dry rotted too.
The 64-71 Thunderbirds have the same system and those hoses are available at Thunderbird parts houses, but I don't know if they're the same. I just finished restoring a 66 LTD 4-door hardtop. I used my old hoses as a pattern and made new ones out of an inner tube and stapled them together. Email and we can talk.
|
| Question From:
PJ
2011-09-15
1968 Ford XL Convertible
| Question:
We just started the restoration of our 1968 Ford XL Convertible! What a nightmare! This is not fun! We took it all apart, found a restoration shop we thought would do us right. So far they are 100% over their estimate and are apparently charging us 40 hours a week, for every week it is in the shop. Do you think they are really working on it 40 hours a week or are we being charged shop time?
Response(s)
You need to show up every Friday and have them show you what they have done by the hour. This should answer your question. They should only charge you for work performed, not for it just sitting there!
|
| Question From:
jeff bonie
2011-09-15
1964 Ford Custom 500
| Question:
Looking for or how to get rear emblem on gas tank door on my 64 Ford Custom 500 or mine restored. Thanks.
Response(s)
|
| Question From:
al
2011-09-15
1963 Ford Galaxie Convertible
| Question:
I need to replace the outer wheel house on both sides, any manufacturer make replacements?
Response(s)
|
| Question From:
scott helmbeck
2011-09-14
1963 Ford Country Sedan
| Question:
Are the 1963 qtr side mouldings the same length on a Country Sedan Wagon as they are on a 4 door sedan?
Response(s)
no the wagon mouldings are longer than the sedan mouldings you will need the mouldings from a wagon
|
| Question From:
Hank McMillan
2011-09-13
'59 Galaxie 500 hardtop convertible
| Question:
Need trunk rear chrome (the long piece) for a '59 Galaxie 500 hardtop convertible - will take reproduction, new OEM or used in good condition - you can call me on my cell at (478) 719-8849.
Thanx-
Hank
Response(s)
|
| Question From:
Ryan Shipton
2011-09-11
1968 Galaxie 500
| Question:
Looking for wiring schematics diagram for a 68 Ford Galaxie with a 302.
Response(s)
|
| Question From:
daniel hines
2011-09-11
1965 Ford Galaxie 500
| Question:
I need to find the box that holds the heater core on the firewall of a 65 Ford Galaxie 500 this car has factory air conditioning I found one but it was the wrong style it was for one without air, any suggestions would be helpful.
Response(s)
daniel i have one iam not useing its not new buts factory u can have it the core to glade to help
daniel i have one iam not useing its not new buts factory u can have it the core to glade to help
|
| Question From:
Roy Maricle
2011-09-11
1963 Ford Galaxie - Model 63 B
| Question:
I want to replace the Trunk Floor in my Classic car But I am having a hard time finding a factory picture or Diagrame to use as a blue Print to Rafferance From?
Response(s)
|
| Question From:
jack kaser
2011-09-09
1963 Galaxie xl 500
| Question:
Looking for a picture of a 1963 1/2 Galaxie r code wiring lay out.
Response(s)
the wiring diagram is the same as for the z code
|
| Question From:
ALP DUNDAR
2011-09-07
1969 Ford Galaxie 500 4 dr hardtop
| Question:
I have 69 Galaxie 500 4 dr hardtop with engine 390. I am looking steering wheel of my car.
Thank you in advance and best regards. ALP DUNDAR
Response(s)
|
| Question From:
Derek
2011-09-07
1965 Ford Thunderbird 390 cid v8
| Question:
I have owned a 1965 Ford Thunderbird since it was new. I am now replacing a rubber bearing sleeve on the steering column upper shaft. Is there a spring that should be underneath the steering wheel as I noticed that in the repair manual. I did not find it when I removed the steering wheel. Do you have any instructions on how to remove and replace the bearing sleeve? Thank you for any information.
Response(s)
|
| Question From:
jeff tillerson
2011-09-07
Ford Galaxie 500
| Question:
What is the best way to clean and polish the aluminum trim that runs down the center of the body from front to back? I have a 68 Ford Galaxie 500 2DR fastback. They have some oxidation on the outside of the trim.
Response(s)
brasso will work or you can use 3000 grit wet/dry sand paper if its real bad . if you use the 3000 grit paper use it with dish soap in the water in a bucket and keep the paper wet .
Quadruple zero (0000) steel wool from any auto parts store. Except NAPA, they are useless. Works AMAZINGLY.
After you use 3000 grit sandpaper, go to auto parts store and buy some "never dull pads". It comes in a can and smells like kerosene.
|
| Question From:
Ricardo Ward
2011-09-06
1972 LTD conv
| Question:
1972 Ford LTD, eng excellent/new, want to restore with limited funds availible. Looking for honest reliable, shop to do the work in S. Calif. car is complete with good body and frame. garaged!
Response(s)
|
| Question From:
Randy Gibson
2011-09-05
1965 LTD 4dr Hdtp
| Question:
I need front clip attaching hardware, and spring spacers to raise the car, front and rear. Thank you.
Response(s)
|
| Question From:
John
2011-09-05
1963 Galaxie 500
| Question:
Need to know the proper routing for the heater hose from the water pump to the heater core and out. Also, I am looking for a windshield washer tank.
Response(s)
|
| Question From:
Jerimia heffner
2011-09-04
1967 Ford Galaxie 500
| Question:
Whats compatable with my 1967 Ford Galaxie 500 heater core 289 sml blk
Response(s)
a 67 or 68 heater core will work
|
| Question From:
John Zimmer
2011-09-03
1964 Galaxie 500 converitble
| Question:
The family and I opened the head covers and found plastic pieces looking like a broken grommet or a bushing. Are there any plastic parts in the heads? This is a family project that our children are very interested in and involved with. Any help is greatly appreciated.
Response(s)
sounds like you are refering to the valve stem seals
|
| Question From:
Jerome
2011-09-03
1962 Galaxie 500 (2-door)
| Question:
I locked my keys to the trunk of my 1962 Galaxie 500 (2 door)in the trunk. Are there any options short of a locksmith to retrieve the keys?
Response(s)
remove the rear seat and you can crawl through to get the keys
|
| Question From:
James Ross
2011-09-03
1966 Ford Galaxie 500 convertible
| Question:
Looking for air conditioning options for 1966 Ford Galaxie 500 w/ 352 ci. Not originally equipped. Thanks for your input.
Response(s)
try classic auto air .com
|
| Question From:
steve huffman
2011-09-02
1968 Galaxie 500
| Question:
Where is the VIN located on a 1968 Galaxie 500 convertible?
Response(s)
For a 68 LTD 2dr hardtop, there should be a tag at the passenger side of the dashboard. It is actually attached to the body. If you have the front fenders off, there is a metal plate on each end of the cowl vent box (where the windshield wiper linkage is) and firewall that has it stamped on it.
|
| Question From:
Tom
2011-08-31
1969 xlgt convertible
| Question:
Does anyone know of a company selling a replacement interior kit for '69 Xl convertible?
Thanks
Response(s)
macs autoparts.com
|
| Question From:
Robert Janik
2011-08-31
1968 Galaxie XL. 2 door. 390 v-8
| Question:
Where is the safety neutral switch on my 1968 galaxie. 390 v-8. floor shift automatic. c-6 transmission. Car will not start with key. Need to know where the safety switch is so I can replace it.
Response(s)
The neutral safety switch for a 1968 with an original console and horse shoe shift is located under the transmission selector inside the console.
|
| Question From:
Joe D Cruz
2011-08-31
68 Torino
| Question:
I bought a 68 Fairlane 500 four door about a year ago. It was a parts car for my 68 GT Torino. My car came with a single wire sending unit while the four door has a 3 pin connector for the low fuel light. How do I wire this? I'm only going to use the fuel level. Out of the other 2 pins, is one of them a ground.
Response(s)
|
| Question From:
Ronald Williams
2011-08-31
Ford Galaxie 500 xl 2 door hard top
| Question:
Where can I find the fuse block for 1962 Ford Galaxie 500 xl I can't find fuses.
Response(s)
it is located on the headlight switch. you will need to remove the switch to see the fuses
|
| Question From:
jerry miller
2011-08-30
1959 Ford Skyliner Galaxie 500
| Question:
How do I remove the steering wheel from '59 Ford so I can repaint it.
Response(s)
you will have to remove the horn button then the center nut once you have that off then you will need a steering wheel puller to get the wheel off the shaft . you will be able to find a puller from any auto parts store
|
| Question From:
jeff tillerson
2011-08-30
68 Ford Galaxie 500
| Question:
I have a 68 Ford Galaxie 500 fastback 2dr with the moulding the goes down the center of the body from front to rear. I need to replace some of the nylon clips and don't know where to find them? Any ideas!
Response(s)
try dearbornclassics.com or macs auto parts .com
|
| Question From:
Paul Weiss
2011-08-27
1969 Galaxie XL
| Question:
I have a 1969 Galaxie XL with a 429 automatic. Does anyone know who makes street headers for this application? I've done a lot of internet searching and so far no luck
thanks
Response(s)
crites .com
This link will get you started
http://fordpowertrain.com/FPAindex/Galaxie1.htm
|
| Question From:
Jim
2011-08-27
1964 Galaxie 500 4 door sedan 289
| Question:
Where is reverse light switch located on a 1964 Galaxie 500 4 door sedan 289 automatic 2 speed trans
Response(s)
It should be located on steering column under the dash.
|
| Question From:
sharon grimm
2011-08-25
1967 ford galaxie 500
| Question:
My 1967 Ford Galaxie 500 has a front divers window that seems to be completely stripped out. I can only pull the window up and push it back down. What part do I need and where can I get one? Thanks!
Response(s)
|
| Question From:
David Shunkwiler
2011-08-25
1963 Galaxie
| Question:
I have a 1963 Galaxie "box top" with a stock 289. I would like to put headers on it. Can I get a recommendation on some headers that will fit this applicaiton?
Response(s)
there are several on ebay at a very resonable price
|
| Question From:
Gary Brown
2011-08-22
1966 Ford Galaxie 500
| Question:
Working on a 1966 Galaxie 500 cruise o matic colume shifter problem. Can anyone tell me where I can find or download a diagram or exploded view?
Response(s)
|
| Question From:
Michael J. Spallone
2011-08-22
1967 Ford Galaxie XL Fastback
| Question:
Will the door and quarter glass from a 66 Galaxie fastback work on a 67 Galaxie xl? Is the 67 a freak year, tried to purchase door latches from 66 said they wouldn't work? Can't believe Ford would make parts just for one year.
Response(s)
you will need to use the glass from a 67 or 68 model car
|
| Question From:
wayne ritchison
2011-08-21
1965 Ford Galaxie 500
| Question:
What automatic trans. was used in a 1965 Galexie 500 with a 390 cid engine?
Response(s)
fords c6 for the fe series engines
|
| Question From:
gary thompson
2011-08-20
1967 Galaxie 500
| Question:
I need 1967 Galaxie rear package tray can you help to find one thanks
Response(s)
|
| Question From:
Tom Lawson
2011-08-20
1963 galaxie xl 500 390
| Question:
What is the trick to installing a fuel pump without removing the PS pump and getting the shaft under the cam lobe?
Response(s)
You can push the PS pump to the side if you loosen the bolts on the mounting brackets a bit, to give you more room, also if you can rotate and take off the fuel filter canister ,this will give you some more flexabilty to re install the pump. Once you get the bolts for the pump started by holding the pump onto the block to depress the arm, tightening them up will pull the pump into place.
|
| Question From:
John
2011-08-20
67 Galaxie 500
| Question:
I am looking for a steering wheel and horn ring for a 1967 Galaxie 500. Also trying to locate power brake booster. Any guidance is greatly appreciated.
Response(s)
|
| Question From:
victor zamora
2011-08-19
1968 Ford Galaxie Country Squire
| Question:
I need the panels imitation wood for the Galaxie Country Squire 1968, where can buy?
Response(s)
|
| Question From:
Andy weickinger
2011-08-19
1967 Galaxie 500 4 door
| Question:
Hi i own a 67 Galaxie 500 4 door with 289 engine in original condition. I found him a few weeks ago in a container from a old lady. She has forgotten the car since 15 years. Brakes were frozen but first key turn it runs :) now my question: I found in the trunk a little vent...looks like a air vent...for what is it...it has 2 hoses and they go in the floor. Sorry for the maybe stupid question but it's my first (and last) Galaxie. I love this car and I will ship it end of the month to Germany where I originaly come from. I like to know as much as I can about my "baby". Cheers from Vancouver Andy.
Response(s)
Some 68 Galaxies had a hot air rear window defroster that was mounted in the trunk and blew up through the package tray at the window. Just a guess. You could send a picture.
|
| Question From:
Mike Rodriguez
2011-08-19
1963 Mercury Colony Park Station Wagon
| Question:
I am looking to install air conditioning in my 63 Mercury Colony Park wagon. Will the Classic Auto Air Perfect-Fit for a 63/64 Ford Galaxie be a direct bolt in for my wagon? If not what will I need to do to retrofit the kit?
Response(s)
|
| Question From:
BUTCH
2011-08-19
Ford
| Question:
I have a 70 model XL Convertible with bucket seats with automatic transmission, Where can I find a floor shifter handle to fit this model??
Response(s)
|
| Question From:
Matt
2011-08-18
1969 Ford Galaxie 500 XL
| Question:
I am wondering where I can find interior, and exterior parts for a 1969 Galaxie, we're really just trying to restore it with new parts. I've looked every where and I've had no luck. I've tried dearbornclassics.com and they don't have every part as well. My father recently overhauled the original engine, a 460. It's all electric now, its got an aod transmission with overdrive now. Its a nice car, its been in the family for over 30 years and running every year, I would really appreciate any help as to where I can find parts for it, thank you.
Response(s)
Macs autoparts sells it all
|
| Question From:
leon darnell
2011-08-16
1965 Galaxie
| Question:
Looking for the chrome lip at the front of the hood. 1965 Ford Galaxie LTD. also wheel well chrome.
Response(s)
|
| Question From:
Richard
2011-08-16
1962 Galaxie 500
| Question:
I have a 1962 Ford Galaxie 500. Is there a fuse box? and if so where?
Response(s)
ita located on the headlight switch . you will need to remove the switch to get to the fuses witch are glass fuses
|
| Question From:
john mitchell
2011-08-16
1962 Galaxie,2 dr post
| Question:
1962 Galaxie, 2 dr post with 292 3 speed. I swapped out the 292 for a 1963 390 with early 4 speed. I used a 1962 352 b/housing, fork and flywheel with a zoom diaphragm clutch. My problem is I can't get enough clutch and still have freeplay to release clutch and put it in gear with out grinding. any ideas will be appreciated. thanks
Response(s)
|
| Question From:
corey
2011-08-15
1967 ford galaxie 500
| Question:
my 67 galaxie 500 coupe has four seat belts i need to add another one to the rear seat how do i remove the seat
Response(s)
lift up on the front of the bottom seat and pull it out. there are 2 bolts at the bottom of the back rest. remove those and pull the seat down.
|
| Question From:
Jerry Wilson
2011-08-15
1963 Ford Country Squire
| Question:
I need replacement parts for a 1963 Country Squire restoration.
Response(s)
|
| Question From:
rusty hammer
2011-08-14
1969 galaxie convertible
| Question:
How do you remove chrome exterior parts such as around windows / top of doors and around well for conv top...."its a 69 Galaxie convertible"
Response(s)
|
| Question From:
Rocky
2011-08-13
1964 Ford Galaxie 500 Convertible
| Question:
I have a 64 Galaxie convert. Only drive it a few times a year. Last year I drove at dusk and turned on my headlights but to my dismay they did not work. I tried my brights and they worked... all 4 went on... but no low beams by themselves.
Checked for fuse but found none. Just drove the car for the first time today 1 year later... now there are no brights. Parks work.... tail lights work... brakes work... dash & interior works...but no headlights. I found the fuse box under the dash on the firewall above the brake pedal, but no fuse for "headlights". I looked up from below to see of there was a fuse mounted to the headlight switch like my 1959 ford... but saw none. I tried to follow the wire to see if I could find a fuse somewhere, but traced it all the way to the headlights and found none. Where is the headlight fuse on a 64 ford galaxie? And wouldn't there be one fuse for both low beams and brights? Why might all 4 brights have worked when my low beams did not? (Could both low beams coincidentally burned out at the exact same time?) Each of the 4 lights work when jumper wire tested. Please advise.
Response(s)
try replacing the dimmer switch. if that doesnt fix the problem then you will need to replace the headlight switch.
|
| Question From:
William White
2011-08-13
1972 Ford LTD Convertible
| Question:
Looking for the front passenger side wheel well molding for a 1972 Ford LTD convt. Do you have one for sale I had an accident with my car
Response(s)
|
| Question From:
mike gehring
2011-08-13
1965 Galaxie 500
| Question:
How hard is it to change the frame off of a Galaxie 500 (1965)?
Response(s)
|
| Question From:
anthony russell
2011-08-13
GALAXIE 500 1965--FLOOR SHIFT FX CRUISEO
| Question:
65 Galaxie FX Cruise-O-Matic - I dropped valve body to replace parking pawl. I can't get spring and pawl to stay in position on rachet while installing. Do I need to loosen or remove rachet to install? What do you use to hold pawl and spring in while doing so? Old Anthony, old dog needs to learn new trick.
Response(s)
|
| Question From:
jim
2011-08-12
1963 Ford Galaxie
| Question:
Can you replace the power steering on a 1963 Ford Galaxie with the power steering system from a 1966 Ford Galaxie?
Response(s)
|
| Question From:
Kirby J. Ransom
2011-08-12
Ford Galaxie
| Question:
I am having my Ford restored and I think this guy is cheating me. How long does it take to install wire harness and run wires to respective locations? How much should a standard carburetor cost with kit and gaskets for Galaxie 500 with 427 engine?
Response(s)
|
| Question From:
Styledaddy
2011-08-11
1965 ford galaxie 4 door hard top LTD
| Question:
Will the front and back bench seats from a 65 ,2 door hard top fit a 65,4 door hard top.
Response(s)
|
| Question From:
Corbin Ford
2011-08-11
1967 Galaxie convertible
| Question:
Where can I get a body mount kit for a 67 Galaxie convert.?
Response(s)
|
| Question From:
Kris Strobeck
2011-08-11
62 Galaxie 500 XL
| Question:
What kind of transmission fluid do I put in?
Response(s)
|
| Question From:
Cindy Bagley
2011-08-11
1967, 1968 galaxie 500
| Question:
Where can I find original build sheets for 1967 and 1968 Galaxie 500? Also, did Ford ever make a 1968 Galaxie with a 1967 front clip?
Response(s)
|
| Question From:
Beaniman
2011-08-11
69 ford Galaxie 500 convertible
| Question:
Were can I get a manual for a 69 Ford Galaxie 500 convertible?
Response(s)
|
| Question From:
Beaniman
2011-08-11
69 ford Galaxie 500 convertible
| Question:
I have a 69 Ford Galaxie 500 convertible with a 351 winsler. I pulled out the motor. Rebuild it, and put it back in. It started up fine. My problem is it will not shift out of park. What should I check first?
Response(s)
If you had the transmission rebuilt make sure they put the correct torque converter. The 351 Windsor was a mid-year engine for the 69 Galaxie and not everyone knows the correct parts without some help. I had the same thing happen to me. Luckily I had written my name and things on the old torque converter so they were able to find the correct one.
|
| Question From:
Chris Baron |
|
| |
Ford Restoration Q&A